PYLE Audio Stereo System PLCD22MRP User Guide

PLCD22MRP

OWNER'S MANUAL

Shipboard Audio System

• PLL Synthesizer Stereo Radio

• Digital Compact Disc Player

• Automatically Memory Storing

• Direct Track Access

• Program CD Tracks

• Electronic Shockproof (ESP) Function

www.pyleaudio.com

INSTALLATION

TAKE OUT SCREW BEFORE INSTALL

Before install the unit, please remove the

two screws.

3. Use the glue paper to stick the two

mounting bracket to the back of the

dashboard. The screw holes of the

brackets must respectively aim at the

mounting holes in order to fix the unit

to the dashboard.

Take out screw before install.

Mounting Bracket

Dashboard

NOTE: This unit is installed on the ship,

so you should use two pieces of plastic

film (30mmX20mm) supplied with the unit

to seal the two holes after remove the

screws. And this will be waterproof.

4. Open the two pieces of rubber cover

on the unit to display the four screw

holes, and then use four screws

INSTALL THE UNIT

1. According to the mounting paper

supplied with the unit, determine the

mounting location in the dashboard,

and then stick the paper to the

dashboard.

(M4X30) to mount the unit to the

dashboard with the mounting plate

between the dashboard and the unit.

Dashboard

Mounting plate

Mounting paper

Rubber cover

Mounting plate

Rubber cover

Screw (M4x30)

2. Then cut and remove the part of the

dashboard in a rectangle shape the

same as the hatching area on the

mounting paper. And then drill four

mounting holes (ø5) in the exact

position also according to the mounting

paper.

Note: If you don’t install the unit

according to the installation instructions

above, the main unit may be not up to

the IPX5 waterproof standard.

Dashboard

Mounting Location

Mounting holes

WIRING CONNECTION

(BLACK)

WIRING REMOTE

CONNECTOR SOCKET

(YELLOW)

RED Rch

WHITE Lch

ANTENNA

CONNECTOR

AUX IN CABLE

FUSE

RED

Rch

Lch

RCA CABLE (GREY)

BLUE

WHITE

POWER ANTENNA

RED

IGNITION SWITCH (ACC+)

MEMORY BACK-UP (B+)

GROUND (B-)

YELLOW

BLACK

WHITE

GREY

FRONT Rch

SPEAKER

FRONT Lch

SPEAKER

WHITE/BLACK

GREEN

GREY/BLACK

VIOLET

REAR Rch

SPEAKER

REAR Lch

SPEAKER

GREEN/BLACK

VIOLET/BLACK

OPERATION

9 15 11

18 3 19 2 4 13

16 10 12 17 20

14 22

25 1

When pull open the disc cover:

26 5

OPERATION

CONTROL & FUNCTIONS KEYS

This unit is a marine rated wired remote control made using a modified controller or

similar layout. It is capable of operation specified functions on the marine AM/FM/CD

receiver and the marine AM/FM/Cassette receiver. The body, buttons, controls and

display need to be UV and water-resistant. It includes and LCD and an illumination

circuit. The flat body should be watertight and the circuit board clear coated.

1 Power button

Press the button (1) shortly to turn on/off the head unit.

Press button (1) for more than 3 seconds, the button is operated to initial volume

control button. When system power turns on, the volume is set to initial volume

level.

2 MUTE button

In RADIO/AUX IN mode, press MUTE

button (2) to activate mute function and

“MUTE” will appear on the display. Press the button once again to release mute

function and return the volume to the last position before it was muted.

In CD (or CASSETTE) mode, press

CASSETTE) player. Press it again to resume play.

MUTE button (2) to pause CD (or

3 VOLUME +/- buttons

Press VOL

buttons (3) to increase/decrease volume level.

OPERATION

4 MODE SELECTION button

Press the MODE button (4) to step sequentially through the following sources:

e.g. radio mode to CD mode (or cassette mode) to AUX in mode.

5 BAND SELECTION button

FOR WEATHER BAND VERSION ONLY:

Press the BAND button (5) to step sequentially through the following bands: FM1,

FM2, AM, WX.

6 TRACK/SEARCH/TUNE buttons

• STATION SELECTION (FOR RADIO OPERATION)

Press

buttons (6) shortly to activate automatic seek function. Press for

more than 3 seconds until “MAN” appears on the display, the manual tuning

mode is selected. If both buttons have not pressed for several seconds, they

will return to seek tuning mode and “AUTO” appears on the display.

• STATION SELECTION (FOR WEATHER BAND OPERATION)

Press

buttons (6) shortly to select channel forward or backward. The range

of selecting forward or backward is CH1~CH7 Channels.

• CASSETTE REWIND/FORWARD (FOR CASSETTE OPERATION)

Press

buttons (6) to activate the cassette fast forward or rewind.

• SELECT TRACKS (FOR CD OPERATION)

Press the

track.

Press the

buttons (6) shortly to move to the following track or the previous

buttons (6) for more than 3 seconds to activate fast forward or

rewind of the disc. Disc play starts from when you release the button.

7 SCAN button

• SCAN (FOR RADIO OPERATION)

Press SHIFT/SCAN button (7) to scan through strong stations in the current

band. Radio pauses for five seconds at each strong station. At each time the

frequency is flashing on the display. Press SHIFT/SCAN button (7) again to

listen to current station.

8 Liquid Crystal Display

Exhibit the number, the current disc and the current track, and other activated

functions on the display (8).

OPERATION

INSTALLATION HARDWARE

REMOTE

MOUNTING BRACKET

BASE

HOLDER

SCREW (ø4X50)

NUT

INSTALLATION DIAGRAM

1. First insert the hooks on the base into the slots of the holder to install the base to

the holder.

2. Select the proper object, then place the remote mounting bracket on the base and

let the object go through the base and the mounting bracket.

OPERATION

3. Align the screw holes on the holder with the screw holes on the base and the screw

holes on the bracket, then use the two screws (ø4X50) and nuts to fix the bracket,

the base and holder to the proper location.

4. Last install the remote control to the holder. See below, align the four hooks on the

holder with the four slots on the remote control.

WIRE

OPERATION

• SWITCHING ON/OFF THE UNIT

Switch on the unit by pressing any

button (except EJECT (4)). When

system is on, press POWER button (9)

to turn off the unit. When system power

turns on, the system is returned to

previous mode.

Adjust bass level by VOLUME button

(11) or VOLUME button (12).

Treble

Press SEL/MENU button (10) three times.

Adjust treble level by VOLUME button

(11) or VOLUME button (12).

Balance

Press SEL/MENU button (10) four times.

Adjust sound balance between left and

right speakers by VOLUME button (11)

or VOLUME button (12).

• DISPLAY THE DISC SLOT

Press the hook (7) of the plastic disc

cover then poke it at a slight downward

force to let the cover open, then you

can see the disc slot (5).

Fader

Press SEL/MENU button (10) five times.

Adjust sound balance between front and

rear speakers by VOLUME button (11)

or VOLUME button (12).

Hook

MENU SELECTION FUNCTION

Hold press SEL/MENU (10) for several

seconds to enter menu select function,

then step short press SEL/MENU (10) to

select different set mode and separately

to press VOLUME button (11) or

VOLUME button (12) to select your

requisite as following order.

When you want to close the disc cover,

push the hook into proper location at

a horizontal force.

BEEP ON/OFF

CLOCK ON/OFF WHILE POWER OFF

FREQ/CLOCK/NO PRI PRIORITY

PROGRAM POWER ON VOLUME LEVEL

USA/EUR

12 HOURS/24 HOURS

For detailed operations, please see below:

BEEP ON/OFF

Hold press SEL/MENU button (10) for

several seconds, when BEEP ON/OFF

appears, press VOLUME button (11) or

VOLUME button (12). to select BEEP

on or BEEP OFF. When beep on, the beep

in generated when every button is pressed.

When beep off, the beep is disabled when

press any button.

• SOUND ADJUSTMENT

Press SEL/MENU button (10) shortly

to change audio mode through volume,

bass, treble, balance, and fader mdoes,

Press VOLUME button (11) or

VOLUME button (12) to adjust the

selected mode. When the currently

displayed function has not been

adjusted for several seconds, the mode

shall return to volume position and

display will return to normal radio, CD

display.

Program power on volume level

Hold press SEL/MENU button (10) for

several seconds, when BEEP ON/OFF

appears, press SEL/MENU button (10)

shortly one time to select “program power

on volume level” mode. And then you can

press VOLUME button (11) or VOLUME

button (12) to select the level when the

unit turns on.

Volume

Bass

Treble

Balance

Fader

Volume

Press SEL/MENU button (10) one time.

Adjust volume level by VOLUME button

(11) or VOLUME button (12).

Notes:

USA/EUR

Hold press SEL/MENU button (10) for

several seconds, when BEEP ON/BEEP

OFF appears, press SEL/MENU button

(10) shortly two times to select “USA/EUR”

mode. And then you can press VOLUME

The unit is initially set to volume mode.

Bass

Press SEL/MENU button (10) two times.

OPERATION

button (11) or VOLUME button (12) to

select USA or European radio frequency

spacing.

- USA radio spacing is 200k for FM and

10k for AM. This is the default frequency

spacing.

- European radio spacing is 50k for FM

and 9k for AM.

VOLUME button (12) to set 24 hours

mode or 12 hours mode.

- When the currently displayed function

has not been adjusted for several

seconds, it will exit menu set mode.

- When you have set CLOCK ON during

power off state, LCD backlight will be

turn on together.

CLOCK ON/OFF while power off

Hold press SEL/MENU button (10) for

several seconds, when BEEP ON/OFF

appears, press SEL/MENU button (10)

shortly three times to select “clock on/off

while power off” mode. And then you can

press VOLUME button (11) or VOLUME

button (12) to select if the clock is to be

displayed while power off.

FREQ/CLOCK/NO PRI priority

Hold press SEL/MENU button (10) for

several seconds, when BEEP ON/OFF

appears, press SEL/MENU button (10)

shortly four times to select

DISPLAY INFORMATION

When pressed quickly, the DSP button (1)

changes the display as follows.

- In AM/FM mode:

-> Frequency ->CLOCK ->

- In CD mode:

-> CD ->CLOCK ->

Each display time is 5 seconds, the display

will return to the first position after 5

seconds.

SET THE CLOCK

Press the DISP button (1) shortly until the

clock is shown on the LCD display. Then

hold down DISP button (1) until the clock

flashes. Then press the TUNE button

(17) clockwise to change hours or rotate

the TUNE button (16) to change minutes.

“FREQ/CLOCK/NO PRI priority” mode.

And then you can press VOLUME button

(11)or VOLUME button (12) to select

frequency priority or clock priority or no

priority.

MUTE

In radio/AUX IN mode, press

/MUTE

- When select Frequency Priority:

The frequency will appear on the unit

all the while. Pressing DSP button (1)

while in Frequency Priority will temporarily

display clock and then returns to

frequency display.

button (3) to mute audio level. Press the

button again to release mute function.

EQUALIZATION

Press EQ button (19) to turn on equalization

function and to select desired audio mode.

There are five kinds of mode as below:

- When select Clock Priority:

The clock will appear on the unit all the

while. Pressing DSP button (1) while in

Clock Priority will temporarily display

selected station frequency (in RADIO

mode) or track number (in CD mode)

and then returns to clock display.

- When select No Priority:

When the frequency appears on the unit,

pressing DSP button (1) will display

clock and it will not return to frequency

display until DSP button (1) pressed

again. When the clock appears on the

unit, pressing DSP button (1) will display

frequency information.

DSP OFF FLAT

POP

JAZZ

CLASSIC

ROCK

LOUDNESS

Press LOUD (DIM) button (15) shortly to

reinforce the bass output and display will

show “LOUD”. Press it again to release

this function.

MODE SELECTION

Press MODE button (6) to sequence through

primary operating modes in the following

order: radio > CD.

If playback media (CD) is not loaded into

mechanism, CD mode will be skipped.

12hours/24hours

LIQUID CRYSTAL DISPLAY

Exhibit current frequency and activated

functions on the display (8).

ILLUMINATION

Press LOUD (DIM) button (15) for more

than 2 seconds to adjust the brightness

Hold press SEL/MENU button (10) for

several seconds, when BEEP ON/OFF

appears, press SEL/MENU button (10)

shortly five times to select

“12hours/24hours” mode. And then you

can press VOLUME button (11) or

OPERATION

of the LCD display backlight.

select CH1~CH7 directly.

RESET FUNCTION

• AUTOMATICALLY MEMORY

STORING & PRESET SCAN

When you pull out the plastic panel covering

the CD opening, you will see the reset

button (26) is placed above the disc slot

(5). It must be activated with either a

ballpoint pen or thin metal object. The

reset button is to be activated for the

following reasons:

-Automatic memory storing

Press AS/PS button (2) for several

seconds, the radio searches from the

current frequency and checks the

signal strength until one cycle search

is finished. And then 10 strongest

stations are stored into the

corresponding preset number button.

-Preset Scan

Press AS/PS button (2) shortly to scan

all station presets saved in memory.

- Initial installation of the unit when all

wiring is completed.

- All the function buttons do not operate.

- Error symbol on the display.

RECOVERING INITIAL VALUE

In radio (AM/FM/WB) mode, press MODE

button (6) for more than three seconds,

the display will appear “EEP INIT”, and all

settings recover factory value.

• STATION STORING

The preset buttons (14) can be used

to store 10 stations in each band (FM

1, FM 2, FM 3 and AM1, AM2) for

convenient access to your favorite

stations.

ESP FUNCTION

If the unit has the electronic shockproof

function, it can be shockproof about

several tens of seconds.

Programming stations

1. Select the desired band, then

tune in the station you want to

store in memory.

RADIO OPERATION

• SWITCHING TO RADIO MODE

Press MODE button (6) shortly to select

radio mode, the radio mode appears in

the display together with the memory

band and frequency.

2. Press and hold one of the preset

buttons (14) for more than 2

seconds until the corresponding

preset button number appears.

Repeat steps 1. and 2. to

• SELECTING THE FREQUENCY BAND

At radio mode, press BAND/ENTER

button (18) shortly to select the desired

band.

program additional stations.

Quick tuning

Select the desired band, then press

one of the ten preset buttons (14).

• SCAN

The reception band will change in the

following order:

Press SHIFT/SCAN button (13) to set

function to scan mode, which scanning

to higher frequency station with

receivable signal and keep on each

station for several seconds.

FM1

FM2

FM3

AM1

AM2

• STATION SELECTION

Press TUNE button (16) or TUNE

button (17) shortly to activate automatic

seek function. Press for more than 3

seconds until “MANUAL” appears on

the display, the manual tuning mode

is selected. If both buttons have not

been pressed for several seconds, they

will return to seek tuning mode and

“AUTO” appears on the display.

FOR WEATHER BAND OPERATION:

Press TUNE button (16) or TUNE

button (17) shortly to choose channel

backward or forward. And the range

of selecting backward or forward is

CH1~CH7. And you can also press

M1~M7 buttons (20~26) shortly to

OPERATION

• REPEAT THE SAME TRACK

Hold press RPT button (22) for several

seconds to continuously repeat the

same track. Press it for several seconds

again to stop repeat.

CD OPERATION

• SWITCHING TO CD MODE

If there is no CD inserted in the driver:

Gently insert the CD with the printed

side uppermost into the CD

• PLAYING ALL TRACKS IN RANDOM

Hold press SHF button (23) for several

seconds to play all tracks on CD in

random order. Hold press again to

compartment until you feel some

resistance. The CD will be drawn into

the driver automatically. CD playback

begins.

If a CD is already inserted in the driver:

Keep pressing MODE button (6) shortly

until the CD mode display appears.

• EJECTING A DISC

cancel the function.

• PREVIEW ALL TRACKS

Hold press SCN button (24) for several

seconds to play first several seconds

of each track on the current disc. Hold

press again to stop intro and listen to

track.

When pull out the plastic panel and

display the disc slot (5), the disc in the

slot will eject automatically.

If insert a disc into the slot to play with

the plastic panel open, press button

(4) to eject the disc.

When the plastic panel is open, long

press button (4), the unit will eject

for some seconds automatically to

detect if there are some small scrip or

other objects in the disc slot and eject

them out.

• PROGRAM CD TRACKS

Use Program function to select up to

32 tracks to play in any order. Program

works by allowing you to select a track

number for each spot in the playing

sequence. A CD must be inserted and

in CD playing mode to use Program.

- How to program CD tracks

1. Press MEM button (20) for several

seconds to enter Program mode,

then “PGM” stars flashing and “P-

01” icon appear on the display.

2. Press button (16) or button (17)

to choose track number. For

• PAUSE PLAYING

Press

/MUTE button (3) to pause

CD player. Press it again to resume

play.

• SELECTING TRACKS

Press TUNE button (16) or TUNE

button (17) to move to the previous

track or the following track. Track

number shows on display.

example, select track 6, then press

MEM button (20) shortly to

memorize it and “P-02” will appear

on the display. So track 6 will be

played first. Thus, you can also

Hold press TUNE button (16) or TUNE

button (17) to fast reverse or fast

forward. When release the button, the

disc will start play from the current

position.

press

buttons (17) and (16) to

choose track number 10 and press

MEM button shortly, then “P-03”

will appear. So track 10 will be

secondly played. Repeat these

operations, and you can program

CD tracks to your need. If you

completed program setting, press

PGM button (21) for several

• DIRECT TRACK ACCESS

Pressing number buttons 0~9(14) (i.e.

19~28) can activate DIRECT TRACK

ACCESS according to your need. For

example, press button (19), and “T-01”

will be flashing on the display. Then

press button (20), “T-12” will appear

and track 12 will be selected to play.

If you don’t press any button when “T-

01” is flashing. After several seconds,

“T-01” doesn’t flash and track 1 is

selected to play. If you select a track

number that doesn’t belong to the

current disc, “NO TR” will appear on

the display.

seconds to play CD in

programmed order.

Note: Using Program function can only

select up to 32 tracks to play in any

order. When you have selected 32

tracks to be programmed. “FULL” will

appear on the display.

When the CD is played in programmed

order by pressing PGM button (21)

for several seconds, pressing it again

OPERATION

for several seconds will exit PGM

mode.

and then press BAND/ENTER

button (18) shortly.

You can also press number

buttons 0~9 (14) can activate

DIRECT TRACK ACCESS to select

your desired track.

When the disc is playing in

programmed order, pressing MEM

button (20) for several seconds will

cancel the all programmed content

and “CLR” appears on the display.

Note:

- If you don’t press MEM button (20)

to carry out program setting, then

press PGM button (21) for several

seconds, “NO-P” will appear.

The unit searches the track after few

seconds, even if the BAND/ENTER

button (18) is not pressed.

2. SEARCHING DIRECTORY OR

FILE NAME

• TRACK/TIME DISPLAY

Press AS/PS (ELAPSE) button (2) to

show running time/remain time of track.

MP3 OPERATION

Press the MP3 button (13) two

times. It enters into “Searching

Directory or File Name” mode. The

unit searches files and directories

by name which is entered by the

user with the VOLUME / buttons

(11&12).

• SELECT SONGS

SINGLE STEP SELECTION:

Press TUNE button (16) or TUNE

button (17) to reverse or advance

the previous song in single step.

DIRECT TRACK ACCESS

- Use VOLUME / buttons

(11&12) to select the characters

A to Z, blank, 0 to 9, _, -, +.

- Press SEL/MENU button (10)

to confirm entry of each

Pressing number buttons 0~9 (14)

can activate DIRECT TRACK

ACCESS according to your need.

For example, press “1” button, “T1*”

appears and “*” is flashing on the

display and waiting for second

number to be input. Then press “2”

button in several seconds, “T12*”

will appear and “*” is flashing and

waiting for third number to be input.

Then press “3” button in several

seconds, “T123” will appear and

track 123 will be selected to play. If

you don’t press any button when “*”

is flashing, after several seconds,

“T12” appears on the display and

track 12 will be played directly. If you

select a track number that doesn’t

belong to the current disc, “NO FILE”

will appear on the display. For MP3

discs, the track selection range is up

to “254”.

characters.

- Press BAND/ENTER button

(18) to start the title search.

In case the selected title is a

directory name, display will show

(‘ ‘), then

- Use VOLUME / buttons

(11&12) to list all songs under

this directory and select the title.

- Press BAND/ENTER button

(18) to confirm and start the

play.

- Repeat the above steps if the

newly selected title is again a

directory.

Note: In this mode, you can also

press the corresponding buttons

listed on the Table 1 below to input

the your desired character to

select the files or directories.

SELECT BY SCAN/MP3 BUTTON:

“Searching track directly” =>

“Searching Directory or File Name”=>

searching from root by VOLUME

/ buttons (11&12) =>searching

from current directory by VOLUME

/ buttons (11&12).

Key Assigned in Searching mode (Table

1. SEARCHING TRACK DIRECTLY

Press the MP3 button (13) one

time to enter into “Searching track

directly” mode. Set desired track

by VOLUME / buttons (11&12),

OPERATION

is directory). The current directory

name is displayed for a second

and the currently playing file name

is displayed. The user can select

the directory or file in the directory

by VOLUME / buttons (11&12).

The selected file can be played by

pressing BAND/ENTER button

(18).

Normal

In MP3 searching

MP3 Searching

Mode Select

ENTER

SCAN

BAND

A, B, C, 1

D, E, F, 2

G, H, I, 3

J, K, L, 4

• PAUSE

Press

M, N, O, 5

/MUTE button (3) to pause

MP3 player. Press it again to resume

play.

P, Q, R, 6

S, T, U, 7

• REPEAT THE SAME SONG

Press and hold RPT button (22) for

several seconds to continuously repeat

the same song. Press and hold it again

for several seconds to cancel repeat

function.

• PLAY SONGS IN RANDOM ORDER

During MP3 operation, press and hold

SHF button (23) for several seconds

to play songs in random order. Press

and hold it again for several seconds

to cancel the function.

V, W, X, 8

Y, Z, SPACE, 9

_,-,+,0

SELECT

Character shift

CHARACTER SELECT

(A, B~Z, SPACE, 0~9,

_,-,+)

VOL UP/DOWN

AS/PS

Backspace

3. SEARCHING FROM ROOT