MAINTENANCE KIT
Type 400
Operating Instructions
Introduction
This manual describes detailed instructions on the operation and notes about the use of this machine.
To get maximum versatility from this machine all operators are requested to read this manual carefully
and follow the instructions. Please keep this manual in a handy place near the machine.
TABLE OF CONTENTS
Trademarks.............................................................................................................1
1. Replace Maintenance Kit
Before Replacing ...................................................................................................3
Checking the contents of the box...............................................................................3
Preparing to replace the parts....................................................................................4
Replacing Parts......................................................................................................5
Replacing the Friction Pad.........................................................................................5
Replacing the Paper Feed Rollers .............................................................................6
Replacing the Transfer Roller ....................................................................................8
Replacing the Fusing Unit........................................................................................10
INDEX......................................................................................................... 12
i
ii
Trademarks
Microsoft, Windows, and Windows NT are registered trademarks of Microsoft@
Corporation in the United States and/or other countries.
Other product names used herein are for identification purposes only and might
be trademarks of their respective companies. We disclaim any and all rights in-
volved with those marks.
Notes:
Some illustrations in this manual might be slightly different from the machine.
Certain options might not be available in some countries. For details, please con-
tact your sales or service representative.
Note
The proper names of the Windows operating systems are as follows:
• The product name of Windows® 95 is Microsoft® Windows® 95.
• The product name of Windows® 98 is Microsoft® Windows® 98.
• The product name of Windows® Me is Microsoft® Windows® Millennium
Edition (Windows Me).
• The product names of Windows® 2000 are as follows:
Microsoft® Windows® 2000 Advanced Server
Microsoft® Windows® 2000 Server
Microsoft® Windows® 2000 Professional
• The product names of Windows® XP are as follows:
Microsoft® Windows® XP Professional
Microsoft® Windows® XP Home Edition
• The product names of Windows ServerTM 2003 are as follows:
Microsoft® Windows ServerTM 2003 Standard Edition
Microsoft® Windows ServerTM 2003 Enterprise Edition
Microsoft® Windows ServerTM 2003 Web Edition
• The product names of Windows NT ® 4.0 are as follows:
Microsoft® Windows NT® Server 4.0
Microsoft® Windows NT® Workstation 4.0
1
2
1. Replace Maintenance Kit
The maintenance kit contains parts necessary for maintaining the printer. When
“Replace Maintenance Kit” appears on the panel display, install the replace-
ment parts included in the maintenance kit.
R WARNING:
• It is dangerous to handle the plug with wet hands. An electric shock
might occur.
R CAUTION:
• The inside of the machine could be very hot. Do not touch the parts with a
label indicating the “hot surface”. Otherwise, it could cause a personal burn.
• When you pull the plug out of the socket, grip the plug to avoid damaging
the cord and causing a fire or an electric shock.
• Be sure to turn off the printer and wait for about an hour before replacing
parts. Not waiting for the printer to cool down can result in a burn.
Note
❒ If you dispose of the used parts yourself, dispose of them according to local
regulations.
Before Replacing
Checking the contents of the box
Check the contents of the box according to the following list. If one or more items
are missing, contact your sales or service representative.
Description
Quantity
Friction pad
3 pcs
⇒ p.5 “Replacing the Friction
Pad”.
Paper feed roller 3 pcs
⇒ p.6 “Replacing the Paper
Feed Rollers”
3
Replace Maintenance Kit
Description
Quantity
Transfer roller
1 pc
⇒ p.8 “Replacing the Transfer
Roller”
1
Gloves
1 pair
Fusing Unit
1 pc
⇒ p.10 “Replacing the Fusing
Unit”.
Preparing to replace the parts
You should replace all the parts included in Maintenance Kit at the same time.
Be sure to replace them in the following order:
A Check the contents of the box for the following items:
• Friction pad
• Paper feed roller
• Transfer roller
• Fusing Unit
• Gloves
B Confirm that the followings are true:
• The power switch is turned off.
• The power cord is unplugged from the wall outlet.
• The interface cable is unplugged from the printer.
Important
❒ Wait about an hour after the printer is turned off to allow internal parts to
cool down before replacing the Maintenance Kit.
4
Replacing Parts
Replacing Parts
C Remove paper from the paper
tray. Place the tray upside down
on a flat surface.
Replacing the Friction Pad
1
Replace all the friction pads in the
tray. The following procedure shows
how to replace the tray's friction pad
(Tray1).
A
Pull out the paper tray until it stops.
ZKEM160E
D Use a sharp-pointed item like a
ball-point pen, to release the two
catches that lock the friction pad.
ZKDX270J
Note
❒ The friction pad may fall off
when the catches are released.
Place your hand over the fric-
tion pad while releasing the
catches.
B While lifting the front side of the
tray, pull it out of the printer.
❒ The friction pad spring may
come off. Be careful the spring
does not fall off and become
lost.
ZKEY140E
5
Replace Maintenance Kit
E Return the paper tray to its origi-
nal position, and remove the fric-
tion pad from the tray.
G If your printer is equipped with
the optional Paper Feed Unit(s),
follow the same procedure when
replacing the friction pad.
Note
1
❒ The friction pad spring may
come off. Be careful the spring
does not fall off and become
lost.
Replacing the Paper Feed
Rollers
Replace all feed rollers including the
printer and the optional Paper Feed
Unit(s). The following procedure
shows how to replacing the paper
feed rollers of the printer.
R CAUTION:
• When lifting the machine, use
the inset grips on both sides.
Otherwise the printer could
break or cause injury if dropped.
ZKEM180E
F Insert the new friction pad in the
A Remove the optional Duplex Unit
paper tray.
if it has been installed.
Attach the center projection of the
new friction pad to the spring and
align the projection of both sides of
the friction pad to the holes of the
paper tray. Then push the friction
pad as shown in the illustration
until it clicks.
Reference
See “Moving and Transporting
the Printer” in the Printer Refer-
ence on the CD-ROM labeled
"Operating Instructions".
B Move the printer to the edge of a
sturdy and stable table or desk.
ZKEM190E
After pushing in the friction pad,
try pushing it several times to
check it is properly installed. If it
jumps back into position due to the
force of the spring, it is properly in-
stalled.
ZKEM110E
6
Replacing Parts
Important
D While sliding the green lock lever
to the right (A), set the new roller
(B). After that, return the green
lock lever to its original position
(C).
❒ Be sure to move the printer hor-
izontally. Moving the printer
facing up on down may cause
the toner to scatter.
1
❒ Do not put the printer on an un-
stable or tilted surface.
Note
❒ If the printer is equipped with
the optional Paper Feed Unit,
do not move the printer and the
unit together, they are not se-
curely attached.
ZKEM130E
C Slide the green lock lever to the
right (A), remove the paper feed
roller (B).
Note
❒ Confirm that the green lock le-
ver secures the roller correctly
by checking if the new roller ro-
tates smoothly.
The illustration shows an example
of the paper feed roller as installed
in the printer.
E If the printer is equipped with the
optional Paper Feed Unit(s), fol-
low the same procedure when re-
placing the paper feed roller.
If you installed two Paper Feed
Units, also replace both paper feed
rollers.
F Place paper in the paper trays and
additional removed paper trays.
Lift the front of the tray, and slide
it carefully into the printer until it
stops.
ZKEM120E
ZKDY150J
7
Replace Maintenance Kit
D Hold the lock levers (green parts),
Replacing the Transfer Roller
and pull them.
A While holding the front cover
with both hands on the left and
right sides, press the release but-
ton to open it.
1
ZKEM200E
E Hold the green parts of the roller
on both sides, and remove the
roller from the printer as shown
in the illustration.
ZKEH120E
B Pull the toner cartridge out of the
printer, while lifting the front
side.
Note
❒ Be sure to place the used car-
tridge on the level place.
ZKEM210E
F Insert the new transfer roller on
the socket with the gear of the
roller positioned on the left.
ZKET110E
C To avoid making your hands
dirty with toner from the transfer
roller. Wear the gloves included
in the maintenance kit.
ZKEM220E
8
Replacing Parts
Important
I Lower the toner cartridge when it
touches the back.
❒ Do not insert the roller on the
back of the socket, or the printer
might be damaged.
1
❒ Insert the metallic part of the
roller on the socket. If you insert
the sponge part of the roller, the
roller might be damaged.
G Push down the green parts of
both sides of the roller until it
clicks as shown in the illustration.
ZKET140E
J Close the front cover by pressing
the left and right side indenta-
tions.
ZKEM221E
Note
❒ When the transfer roller is set,
the transfer roller cover will re-
turn to its original position au-
tomatically.
ZKEH130E
K Take the gloves off and go to p.10
“Replacing the Fusing Unit”.
H Holding the grips of the toner car-
tridge, insert it into the printer
until it stops.
ZKET120E
9
Replace Maintenance Kit
B Lift the lock levers of the fusing
Replacing the Fusing Unit
unit as shown in the illustration.
R CAUTION:
• The fusing unit becomes very
hot. When installing the new fus-
ing unit, turn off the printer and
wait about an hour. After that, in-
stall the new fusing unit. Not
waiting for the unit to cool down
can result in a burn.
1
ZKEX222E
A If the rear cover is attached to the
printer, remove it.
C Pull the fusing unit out.
Note
❒ Proceed to step if the optional
B
Duplex Unit was removed in
step , "Replacing the Paper
A
Feed Rollers".
A Place a finger in the printer's
rear cover finger hole (upper
center) and pull it open.
ZKEX223E
D Pull out the pins on both sides of
the new fusing unit.
ZKEX210E
B Remove the rear cover in a hor-
izontal direction.
ZKEM010E
ZKEX220E
10
Replacing Parts
A Insert the rear cover to the in-
side grooves on both sides of
the printer in a horizontal di-
rection.
E Replace the new fusing unit into
the printer.
1
ZKEX224E
ZKEX221E
F Push the lock levers of the fusing
unit down until it clicks.
B Close the rear cover.
Proceed to step .
I
ZKEX225E
ZKEX211E
G Reinstall the rear cover removed
in step
.
A
H
I
Reinstall the optional Duplex Unit
if it was removed in step , "Re-
A
Note
placing the Paper Feed Rollers".
❒ Proceed to step if the optional
H
Duplex Unit was removed in
Reference
step , "Replacing the Paper
A
See “Movint and Transporting the
Printer” in the Printer Reference
on the CD-ROM labeled "Oper-
ating Instructions".
Feed Rollers".
Print a configuration page to con-
firm that the printer works properly.
Reference
For more information about
printing the configuration page,
see “List/Test Print Menu” in the
Printer Reference is provided as
a PDF file on the CD-ROM la-
beled “Operating Instructions”.
11
INDEX
F
friction pad,
5
fusing unit, 10
P
paper feed roller,
6
T
transfer roller,
8
12
MEMO
13
MEMO
14
GB
GB
EN
USA
G830-8600
Printed in China
GB GB
EN USA G830-8600
|