Roberts Radio Portable Radio Solar Powered DAB Radio User Guide

Solar powered DAB radio with rechargeable battery pack

Please read this manual before use

Controls

(Front)

1. Tuning control

2. Volume control

3. On/Off button

4. Preset button

5. Mode Button

6. Telescopic aerial

7. Signal strength

8. Solar charging level

9. On charge indicator

10. Battery indicator

11. Info button

12. Scan button

If you need any further advice, please call our Technical Helpline on :-

020 8758 0338 (Mon-Fri)

Controls

(Back)

13. DC input socket

14. Line in socket (aux-in)

15. Headphone socket

16. Aerial storage slot

Using the AC adaptor

Your solarDAB radio may be powered either by using an AC adaptor

(supplied) or by using solar power.

For prolonged life, the internal rechargeable NiMH battery pack requires

an external conditioning charge of 24 hours prior to ﬁrst use.

1. Place your radio on a ﬂat surface.

2. Insert the adaptor plug into the DC socket located on the rear of your

radio.

3. Plug the adaptor into a standard 13 amp mains socket outlet. The

display will show the on charge indicator and the battery indicator will

be animated.

4. When the batteries are fully charged, the battery indicator should

show all segments without ﬂashing. Remember to keep the adaptor

connected for a period of 24 hours for the initial charge in order to

ensure optimal conditioning of the batteries.

The AC adaptor should be disconnected from the mains supply and the

radio when not in use.

Note: The mains adaptor which is supplied with your radio is a high-

efﬁciency type, designed to minimise energy consumption, whether the

radio is playing, charging its batteries, or switched off (in standby). Do not

use any other mains adaptor in place of the unit supplied. Such use will

invalidate your guarantee.

IMPORTANT: The mains adaptor is used as the means of connecting the

radiotothemainssupply.Themainssocketusedfortheradiomustremain

accessible during normal use. In order to disconnect the radio from the

mains completely, the mains adaptor should be removed from the mains

socket outlet completely.

If you need any further advice, please call our Technical Helpline on :-

020 8758 0338 (Mon-Fri)

Using solar power

1. In order to recharge your solarDAB radio's batteries using solar power,

positiontheradiosothatitsintegralsolarpanelreceivesdirectsunlight.

The more sunlight that falls on the solar panel - the more electricity it

can generate to power the radio.

8. Keep the solar panel unobstructed and its protective lens free of dirt

and grease. This will ensure best performance with the available

sunlight.

9. The battery indicator

on the display gives an approximate

2. The solar charging level indicator

on the display should

indication of the amount of charge in the batteries. Note that directly

afteraperiodofcharging,thisbatteryindicationmayshowmorecharge

is available than is actually present and so the indicator should only

be used as a rough guide.

be used as a positioning aid to achieve the greatest output from the

solar panel. It works on a bar system similar to the battery indicator.

3. If no bars or showing (or if the icon disappears completely) then there

is no useful light available.

NOTE: Best performance of the solar panel will be achieved when the sun

is directly overhead, and the sunlight is unobstructed by clouds, foliage,

curtains, and the like. In certain situations and poorer light conditions,

the solar panel may not be effective and should not be relied upon as the

primary energy source for standard usage. The solar panel is designed

as a supplementary energy source which under suitable light conditions

is able to contribute up to 100% of the radio's energy requirement.

4. If less than half the available bars are showing, then there is some

power from the solar panel which can supplement the batteries in

operating the radio. The radio may be used and the batteries will last

longer than if there was no solar assistance.

5. If more than half the available bars are showing then there is enough

sunlight for the panel to operate the radio and simultaneously provide

some charge to the battery pack.

The solar panel will only deliver power to the radio, or charge the batteries

under natural sunlight. It will not deliver charge in artiﬁcial light.

Do NOT attempt to charge the batteries by placing the solar panel directly

under any kind of sun-lamp. This will cause irreversible damage to the

radio and may damage the casing.

6. If all of the bars are shown, then there is sufﬁcient power from the

solar panel to charge the battery and to power the radio at a moderate

volume.

7. While it is possible for the solar panel to power the radio in the absence

of the internal battery pack, the radio should not be used in this way.

It is strongly recommended that the battery pack is ALWAYS installed

when the radio is being used.

Operating your radio for the ﬁrst time

For prolonged life, the internal rechargeable NiMH battery pack requires

an external conditioning charge of 24 hours prior to ﬁrst use. Please see

page 4.

1. Remove the aerial from its storage slot at the back of the radio and

carefully screw it into its position on the top left of the radio. Carefully

extend the telescopic aerial.

2. Press the On/Off button to switch on your radio. The display will light

and will show the language options.

3. Scroll through the language options on the display by rotating the

Tuning control.

4. PresstheTuningcontrol toselecttherequiredlanguage.Thecountry

option will then show on the display.

5. Scroll through country options on the display by rotating the Tuning

control.

6. Press the Tuning control to select the required country. Your radio

will automatically begin scanning for DAB radio stations.

3-6

If you need any further advice, please call our Technical Helpline on :-

020 8758 0338 (Mon-Fri)

7. If this is the ﬁrst time the radio is used a quick scan of UK Band 3

DAB channels will be carried out (or of the channels for the selected

region, if different). The display will show "Auto tune selected...".

8. As new stations are detected during autotune the station counter on

the right hand side of the display will increase and stations will be

added to the list.

9. When the autotune is completed the ﬁrst station (in numeric-alpha

order 0...9...A...Z) will be selected. If the radio has been used before

then the last used station will be selected.

10. If the station list is still empty after the autotune your radio will display

"No Signal".

11. If you see the "No Signal" message or if no DAB radio stations are

found it may be necessary to relocate your radio to a position giving

better reception. You should then press the Scan button to rescan

for DAB radio stations.

When your radio has tuned to a station, the signal strength indicator

shows whether there is a strong or a weak signal present. Ideally, at least

two bars should be showing for good reception.

Note: Your radio will remember the station last tuned to when you switch

it off. In addition, if you were listening using the radio's auxiliary input,

the radio will also remember that you were using it in that way. When

you wish to listen to DAB radio again, press the Mode button to reselect

DAB mode.

Selecting a station

1. The top line of the display shows the name of the station currently

being listened to.

2. RotatetheTuningcontroltoscrollthroughthelistofavailablestations.

Note that the arrow pointer on the left side of the display shows the

station that will be tuned to. This may be on the upper or lower line of

the display depending on the direction of scrolling.

2-3

3. PressandreleasetheTuningcontroltoselectthedesiredstation.The

display may show "Tuning..." while your radio ﬁnds the new station.

4. Rotate the Volume control to the required setting.

Note: If after selecting a station the display shows "Not Available" it may

be necessary to relocate your radio to a position giving better reception.

The radio will attempt to re-tune to the previous radio station.

The use of the station presets for storing and selecting favourite radio

stations is described on page 10.

Secondary services

1. Certain radio stations can have one or more secondary services

associated with them. These are supplementary stations which a

broadcaster may transmit at particular times, or for particular events

- the BBC's Daily Service programme is an example.

2. The secondary service will appear in the list of available radio stations

sorted alphabetically. Rotate and then press the Tuning control to

select the desired station. At the end of the broadcast, the radio will

automatically switch to the primary radio station for that service.

If you need any further advice, please call our Technical Helpline on :-

020 8758 0338 (Mon-Fri)

Display modes - DAB

Your radio has ﬁve display modes which can show information provided

by the broadcaster in addition to the name of the radio station:-

1. Press the Info button to cycle through the various modes.

a. Scrolling text

b. Multiplex Name

c. Frequency

Displays scrolling text messages such as

artist, track name, phone in number etc.

Displays the name of DAB multiplex to

which the current station belongs.

Displays the frequency of the DAB

multiplex for the station listened to.

d. Bit rate & audio type

e. Time

Displays the digital bit rate & audio type

for the station being listened to.

Displays the current the time.

Presetting stations

There are 10 memory presets for the DAB waveband.

1. Press the On/Off button to switch on your radio and tune to the

required station as previously described.

2. Press the Preset button. The display shows, either "Preset 1 free",

or the name of the station already stored in Preset 1.

3. Rotate the Tuning control to choose from presets 1 to 10 and press

and hold the Tuning control. Keep the control pressed while the

station name ﬂashes on the lower line of the display and release the

control when the station name re-appears on the upper line of the

display. The station will be stored under the chosen preset button.

Repeat this procedure for the remaining presets as desired.

4. Stations stored in the presets may be overwritten by following the

above procedure.

Recalling a preset

1. Press the On/Off button to switch on your radio.

2. Press the Preset button. The display shows, either "Preset 1 free",

or the name of the station already stored in Preset 1.

3. Rotate the Tuning control to choose from presets 1 to 10.

4. Momentarily press the Tuning button. Your radio will then tune to the

station stored in the preset memory.

3-4

If you need any further advice, please call our Technical Helpline on :-

020 8758 0338 (Mon-Fri)

Finding new stations - in the UK

As time passes new stations may become available. To ﬁnd new stations

proceed as follows:-

1. Press and release the Scan button. The display will show "Auto tune

selected". Your radio will perform a scan of the UK DAB frequencies.

As new stations are found the station counter on the right-hand side

of the display will increase and stations will be added to the list.

Finding new stations - outside the UK

If you are operating your radio in a country other than the UK you will

need to follow these steps. In many countries DAB stations are located

in frequency Band 3. Some countries use the L band frequencies either

instead of or in addition to Band 3.

1. Press and hold the Scan button. The display will list the scan options

available. These include some speciﬁc European countries. For other

regions you will have the choice of Band 3 or L-band depending on

the frequencies in use.

2. Either choose the "Country" option and then choose the required

country, or rotate the Tuning control until "DAB (all)", "Band 3 (all)"

or "L Band (all)" is selected with the arrow on the display.

3. PressandreleasetheTuningcontrol.Yourradiowillscantheselected

2-3

band for available stations.

If you are uncertain regarding the frequencies used for DAB radio in your

location, then select the "DAB (all)" option.

Finding new stations - manual tuning

Normally, you will use the auto tune feature as described above to ﬁnd

new radio stations. Should you need to search for DAB radio stations at

a particular frequency, please use the following procedure.

1. Press and hold the Scan button. The display will list the scan options

available.

2. Rotate the Tuning control until "Band 3" or "L Band" is selected with

thearrowonthedisplay, dependingonwhichfrequencybandyouwish

to tune to.

3. Press and release the Tuning control. The display will then offer

you a range of frequency blocks, named according to the DAB

speciﬁcations

2-5

For Band 3, the frequency blocks are named 5A through 13F

For L Band, the frequency blocks are named LA through LW

4. RotatetheTuningcontroluntilthedesiredfrequencyblockisselected

with the arrow on the display.

5. Press and release the Tuning control to initiate a scan of the selected

frequency.Ifanynewradiostationsarefound,thenthereportednumber

of services will increase, and the new radio stations will be added to

the list stored in the radio.

After scanning, the radio will return to the radio station previously tuned.

If you are uncertain regarding the frequencies used for DAB radio in your

location, then select the "DAB (all)" option.

If you need any further advice, please call our Technical Helpline on :-

020 8758 0338 (Mon-Fri)

System reset

If your radio fails to operate correctly, or some digits on the display are

missing or incomplete, or if you wish to restore your radio to its initial

settings, please carry out the following procedure.

1. Press and hold down the Info button.

2. While keeping the Info button pressed, simultaneously rotate the

Tuning control until the display shows "Reset?".

3. Rotate the Tuning control to Select either "Yes" to reset or "No" to

return to normal tuning.

2-4

4. If you wish to perform the reset operation, rotate the Tuning control

until "Yes" is selected and then press the Tuning control to conﬁrm.

A full reset of your radio will be performed. All presets and station lists

will be erased.

5. Afterasystemresetyouwillneedtoreselectthelanguageandcountry

settings. A scan of the required DAB band will then be performed.

Note: The number in the lower right of the display is a software version

number and is provided purely for reference.

In case of malfunction due to electrostatic discharge, reset the product

(reconnection of power source may be required) to resume normal op-

eration.

If a problem persists our technical staff would be pleased to offer

anyassistanceonoperatingtheradio. Ourtechnicalhelplinenumber

is 020 8758 0338.

Headphone socket

A3.5mm Headphone Socket located on the back of your radio is provided

forusewitheitherheadphonesoranearpiece.Insertingaplugautomatically

mutes the internal loudspeaker.

IMPORTANT:Excessivesoundpressurefromearphonesandheadphones

can cause hearing loss.

Auxiliary input socket

1. Connect a stereo or mono audio source (e.g. CD player, iPod, MP3

player) to the Auxiliary input socket.

2. Press the Mode button to select the auxiliary input. "Line in" will show

on the display.

3. Adjust the Volume control for comfortable listening.

4. When you wish to listen to DAB radio again, press the Mode button

to reselect DAB mode.

If you need any further advice, please call our Technical Helpline on :-

020 8758 0338 (Mon-Fri)

Display backlight

Battery Pack

1. When running the radio on batteries (with or without solar assistance),

the display backlight will be switched on for approximately 12 seconds

when any button is pressed. Note that when the battery is almost

exhausted,theradiowillnotswitchonthebacklightinordertoconserve

energy.

Thebatterypackwhichisbuiltintoyourradioisdesignedtoprovideseveral

years of service. When the batteries can no longer store sufﬁcient energy

to power your radio after having been charged they should be replaced.

Replacement battery packs will be available from Roberts Radio.

2. When your radio is powered by AC mains the display backlight will

be switched on for approximately 3 minutes when any button is

pressed.

Theoldbatterypackshouldberecycledordisposedofinanenvironmentally

friendly way as prescribed by your local regulations.

•

Your radio should not be exposed to dripping or splashing and that

no objects ﬁlled with liquids, such as vases, shall be placed on the

radio.

It is recommended to operate the product such that there is a minimum

distance (10cm recommended) to adjacent objects in order to ensure

good ventilation.

The ventilation of the product should not be restricted by covering it or

its ventilation openings with items such as newspapers, tablecloths,

curtains etc.

General

Do not allow this radio to be exposed to water, steam or sand. Do not

leave your radio where excessive heat could cause damage such as in

a parked car where the heat from the sun can build up even though the

outside temperature may not seem too high.

The name plate is located on the back of your radio.

•

No naked ﬂame sources such as lighted candles should be placed on

the product.

It is recommended to avoid using or storing the product at extremes

of temperature. Avoid leaving the unit in cars in direct sunlight.

Note that normal use of the solar panel by placing the radio in the sun

on a windowsill, in a conservatory or in a similar location is intended and

should not harm your radio.

Speciﬁcations

Circuit Features

Loudspeaker

Output Power

Headphones

Aerial System:

80mm

Power Requirements

Mains

AC 230 volts, 50Hz

only (adaptor)

Batteries

Built in NiMH 3 x AA cell battery pack

Stereo, 3.5mm diameter socket

Battery Life

Solar Power

Up to 27 hours on full charge at moderate volume

Continuous play under adequate sunlight

DAB Band 3

DAB L-band

Telescopic aerial

Internal aerial

Frequency Coverage

DAB Band 3

DAB L-band

174.928 - 239.200MHz

1452 - 1492MHz

The Company reserves the right to amend the speciﬁcation without notice

If you need any further advice, please call our Technical Helpline on :-

020 8758 0338 (Mon-Fri)

Notes

......................................................................................................................................................................................................

Guarantee

This instrument is guaranteed for twelve months from the date of delivery to the original owner against failure due to faulty workmanship or component

breakdown, subject to the procedure stated below. Should any component or part fail during this guarantee period it will be repaired or replaced free

of charge.

The guarantee does not cover:

1. Damage resulting from incorrect use.

2. Consequential damage.

3. Receivers with removed or defaced serial numbers.

N.B. Damaged or broken telescopic aerials will not be replaced under guarantee.

Procedure:

Any claim under this guarantee should be made through the dealer from whom the instrument was purchased. It is likely that your Roberts' dealer

will be able to attend to any defect quickly and efﬁciently but should it be necessary the dealer will return the instrument to the Company’s service

department for attention. In the event that it is not possible to return the instrument to the Roberts' dealer from whom it was purchased, please contact

Roberts Radio Technical Services at the address shown on the rear of this manual.

These statements do not affect the statutory rights of a consumer.

If you need any further advice, please call our Technical Helpline on :-

020 8758 0338 (Mon-Fri)

ROBERTS RADIO TECHNICAL SERVICES

97-99 Worton Road

Isleworth Middlesex

TW7 6EG

Technical Helpline :- 020 8758 0338 (Mon-Fri during ofﬁce hours)

Website: http://www.robertsradio.co.uk

Issue 1

QSC Audio Speaker AD CI52ST User Guide
Quantum Universal Remote 313 User Guide
Radio Shack Cordless Telephone 43 5560 User Guide
RCA Flat Panel Television HD56W151 User Guide
Rikaline GPS Receiver BT Q880 User Guide
Roland Drums TR 606 User Guide
Rotel Power Supply RB 1070 User Guide
Ryobi Thermometer E49IR01 User Guide
Samson Musical Toy Instrument Graphite 25 User Guide
Samsung Automobile Accessories SGH I617 User Guide